Arkless Electronics Transconductance phono stage

Hi-Fi discussion
sq225917
Posts: 616
Joined: Tue Jan 22, 2013 9:28 pm

Re: Arkless Electronics Transconductance phono stage

Post by sq225917 » Tue Jan 30, 2018 4:29 pm

Probably better if you stick to inside the box Jez. Play to your strengths.
One more Paradise left to complete.

Arkless Electronics
Posts: 64
Joined: Mon Oct 16, 2017 5:54 pm

Re: Arkless Electronics Transconductance phono stage

Post by Arkless Electronics » Tue Jan 30, 2018 6:00 pm

let's give it another go then... Make what you currently have as the outputs the inputs. put red at bottom and black at top. make the ones you have as inputs the loading sockets, red at bottom and black at top. Ground post can stay where it is. Move the sockets you have as "Load" to the middle of the panel and they are the outputs, again red at bottom and black at top. if anything about that is less than clear then let me know and I'll draw a diagram and post it here.

sq225917
Posts: 616
Joined: Tue Jan 22, 2013 9:28 pm

Re: Arkless Electronics Transconductance phono stage

Post by sq225917 » Tue Jan 30, 2018 9:07 pm

Like so?

Image


What do you fancy for sockets, Nuetrik gold plated? Do you have PSU sockets and plugs?
One more Paradise left to complete.

Arkless Electronics
Posts: 64
Joined: Mon Oct 16, 2017 5:54 pm

Re: Arkless Electronics Transconductance phono stage

Post by Arkless Electronics » Tue Jan 30, 2018 9:11 pm

Spot on! Great. No I don't have power plugs and sockets in stock but I think I have some reasonable no brand phono sockets that look the part.

sq225917
Posts: 616
Joined: Tue Jan 22, 2013 9:28 pm

Re: Arkless Electronics Transconductance phono stage

Post by sq225917 » Tue Jan 30, 2018 9:25 pm

I'll sort em, easier for cutting that way.

-RCA's ordered.

I'll check my PSU socket supplies tomorrow.
One more Paradise left to complete.

Arkless Electronics
Posts: 64
Joined: Mon Oct 16, 2017 5:54 pm

Re: Arkless Electronics Transconductance phono stage

Post by Arkless Electronics » Wed Jan 31, 2018 12:10 pm

Ah... I'd just got the specs for the phono's... Neutrik NYS367. M10 hole....

sq225917
Posts: 616
Joined: Tue Jan 22, 2013 9:28 pm

Re: Arkless Electronics Transconductance phono stage

Post by sq225917 » Wed Jan 31, 2018 5:52 pm

Yeh 10mm same as my usual Audio Note silver choice, just not as pricey. I'll isolate the signal gnd of the RCA sockets from the case, you can tie them at GND post if you desire.
One more Paradise left to complete.

Arkless Electronics
Posts: 64
Joined: Mon Oct 16, 2017 5:54 pm

Re: Arkless Electronics Transconductance phono stage

Post by Arkless Electronics » Wed Jan 31, 2018 7:12 pm

That's great. The 10mm in fact included the plastic isolation inserts :D

sq225917
Posts: 616
Joined: Tue Jan 22, 2013 9:28 pm

Re: Arkless Electronics Transconductance phono stage

Post by sq225917 » Sat Feb 03, 2018 10:45 am

Alright drilling begins/.I've got a few jobs on today, should be done by three. If you're around I could bring it all straight over, say 5-6pm. I'll bring all my stand-off kits etc, taper drills.
One more Paradise left to complete.

Arkless Electronics
Posts: 64
Joined: Mon Oct 16, 2017 5:54 pm

Re: Arkless Electronics Transconductance phono stage

Post by Arkless Electronics » Sat Feb 03, 2018 1:34 pm

Just seen this... yes that would be great. No need to bring tools.

Post Reply